MEAN 1
Wizard
o.k. am no pro mechanic , but i do most of my maintance to my motorcycles myself . below is a step by step guide on installing a PC111 to your FZ1 , also some of the maps that are downloadable ..
Last edited:
Installing A PC111 ?
- Thread starter MEAN 1
- Start date
MEAN 1
Wizard
available maps to download .
here sample of PC111 maps that are available to download for the FZ1 -
Maps Available:
Name Description Size
M420-000 Zero Map 28 KB
M420-001 Stock exhaust, stock air filter, stock 02 sensor disconnected 28 KB
M420-002 Graves Motorsports slip-on exhaust, Graves velocity stacks, Stock or aftermarket air filter, Stock O2 sensor disconnected 28 KB
M420-003 Leo Vince slip-on exhaust, Stock or aftermarket air filter 29 KB
M420-004 Graves slip-on exhaust, Stock or aftermarket air filter, Dynojet O2 eliminator 76423020 96 KB
M420-005 Two Bros. V.A.L.E. slip-on exhaust, Stock or aftermarket air filter, Dynojet O2 eliminator 76423020 96 KB
M420-005 Yoshimura TRC full exhaust, Stock or aftermarket air filter 96 KB
M420-501 European model-Stock Exhaust, Stock air filter, O2 sensor disconnected 28 KB
M420-502 European model-Carbon Can Company slip-on exhausts, with baffle, Stock or aftermarket air filter 96 KB
M420-503 European model-Carbon Can Company slip-on exhausts, Stock or aftermarket air filter 96 KB
M420-504 German model-Stock exhaust, Stock air filter, O2 Sensor disconnected 96 KB
M420-505 European model- Lazer Hot Cam slip-on exhaust with street legal baffle, Stock or aftermarket air filter, O2 sensor disconnected 96 KB
M420-507 German model-Stock exhaust, O2 sensor disconnected, Stock or aftermarket air filter 96 KB
M420-508 European model-Laser Hot Cam open slipon, Stock air filter, Stock O2 sensor disconnected 96 KB
M420-509 European model-Leo Vinci open slipon, Stock or aftermarket air filter, Stock O2 sensor disconnected 96 KB
M420-510 European model-Akropovic slip-on exhaust with baffle, Stock or aftermarket air filter, O2 sensor disconnected 96 KB
M420-511 European model-Akroprovic Slip-on Exhaust, Stock air filter, O2 sensor disconnected 96 KB
M420-512 European model-Akrapovic full exhaust, Stock or aftermarket air filter, Stock O2 sensor disconnected 96 KB
M420-513 European model-Remus Power Cone open slipon, Stock air filter, Stock O2 sensor disconnected 96 KB
M420-514 European model-Laser Duo Tech slipon, race insert installed, Stock air filter, Stock O2 sensor disconnected 96 KB
M420-515 European Model-Yoshimura slip on with dB killer, Stock air filter, Stock O2 sensor disconnected 96 KB
M420-516 European model-G&G open slip on, Stock or aftermarket air filter, Stock O2 sensor disconnected 96 KB
M420-517 European model, Leo Vinci slipon with dB killer, Stock or aftermarket air filter, Dynojet O2 eliminator 76423007 installed 96 KB
M420-518 European model, Arrow slip-on exhaust with baffle, Stock or aftermarket air filter, O2 sensor disconnected 96 KB
M420-519 European model, Arrow slip-on exhaust, Stock or aftermarket air filter, O2 sensor disconnected 96 KB
M420-520 European model, Devil master Exhaust with baffle, Stock or aftermarket air filter, O2 sensor disconnected 96 KB
M420-521 European model, Devil master Exhaust, Stock or aftermarket air filter, O2 sensor disconnected 96 KB
M420-ALL All Available Maps
here sample of PC111 maps that are available to download for the FZ1 -
Maps Available:
Name Description Size
M420-000 Zero Map 28 KB
M420-001 Stock exhaust, stock air filter, stock 02 sensor disconnected 28 KB
M420-002 Graves Motorsports slip-on exhaust, Graves velocity stacks, Stock or aftermarket air filter, Stock O2 sensor disconnected 28 KB
M420-003 Leo Vince slip-on exhaust, Stock or aftermarket air filter 29 KB
M420-004 Graves slip-on exhaust, Stock or aftermarket air filter, Dynojet O2 eliminator 76423020 96 KB
M420-005 Two Bros. V.A.L.E. slip-on exhaust, Stock or aftermarket air filter, Dynojet O2 eliminator 76423020 96 KB
M420-005 Yoshimura TRC full exhaust, Stock or aftermarket air filter 96 KB
M420-501 European model-Stock Exhaust, Stock air filter, O2 sensor disconnected 28 KB
M420-502 European model-Carbon Can Company slip-on exhausts, with baffle, Stock or aftermarket air filter 96 KB
M420-503 European model-Carbon Can Company slip-on exhausts, Stock or aftermarket air filter 96 KB
M420-504 German model-Stock exhaust, Stock air filter, O2 Sensor disconnected 96 KB
M420-505 European model- Lazer Hot Cam slip-on exhaust with street legal baffle, Stock or aftermarket air filter, O2 sensor disconnected 96 KB
M420-507 German model-Stock exhaust, O2 sensor disconnected, Stock or aftermarket air filter 96 KB
M420-508 European model-Laser Hot Cam open slipon, Stock air filter, Stock O2 sensor disconnected 96 KB
M420-509 European model-Leo Vinci open slipon, Stock or aftermarket air filter, Stock O2 sensor disconnected 96 KB
M420-510 European model-Akropovic slip-on exhaust with baffle, Stock or aftermarket air filter, O2 sensor disconnected 96 KB
M420-511 European model-Akroprovic Slip-on Exhaust, Stock air filter, O2 sensor disconnected 96 KB
M420-512 European model-Akrapovic full exhaust, Stock or aftermarket air filter, Stock O2 sensor disconnected 96 KB
M420-513 European model-Remus Power Cone open slipon, Stock air filter, Stock O2 sensor disconnected 96 KB
M420-514 European model-Laser Duo Tech slipon, race insert installed, Stock air filter, Stock O2 sensor disconnected 96 KB
M420-515 European Model-Yoshimura slip on with dB killer, Stock air filter, Stock O2 sensor disconnected 96 KB
M420-516 European model-G&G open slip on, Stock or aftermarket air filter, Stock O2 sensor disconnected 96 KB
M420-517 European model, Leo Vinci slipon with dB killer, Stock or aftermarket air filter, Dynojet O2 eliminator 76423007 installed 96 KB
M420-518 European model, Arrow slip-on exhaust with baffle, Stock or aftermarket air filter, O2 sensor disconnected 96 KB
M420-519 European model, Arrow slip-on exhaust, Stock or aftermarket air filter, O2 sensor disconnected 96 KB
M420-520 European model, Devil master Exhaust with baffle, Stock or aftermarket air filter, O2 sensor disconnected 96 KB
M420-521 European model, Devil master Exhaust, Stock or aftermarket air filter, O2 sensor disconnected 96 KB
M420-ALL All Available Maps
MEAN 1
Wizard
STEP BY STEP GUIDE
1 Remove the main seat and the passenger
seat.
2 Prop the front of the fuel in the up
position.
3 Lay the PCIII in the tail section temporarily.
Route the PCIII harness
under the tail section and go towards
the front of the bike.
4 Locate the connector from the main
wiring harness to the
injector rail and uplug this
connector (Fig. A).
NOTE: This connector is grey in color.
5 Plug the connectors from the PCIII inline
of the stock wiring harness (Fig.
B).
6 Bolt the fuel tank down into position.
7 Remove the bolt on the left hand side
of thefuel tank bracket and loosen the
right hand bolt enough to route the
PCIII harness underneath it (Fig. C).
8 Reinstall the bracket.
9 Attach the ground wire from the PCIII
to the negative side of the battery
(Fig. D).
10 Install the PCIII in the rear
section of the trunk (Fig. E).
This bike does not have a flat surface
to allow you to use the supp7 Remove the bolt on the left hand side
of thefuel tank bracket and loosen the
right hand bolt enough to route the
PCIII harness underneath it (Fig. C).
11 Make sure all the wires are
routed properly.
12 Reinstall the main seat and the passenger
seat.
1 Remove the main seat and the passenger
seat.
2 Prop the front of the fuel in the up
position.
3 Lay the PCIII in the tail section temporarily.
Route the PCIII harness
under the tail section and go towards
the front of the bike.
4 Locate the connector from the main
wiring harness to the
injector rail and uplug this
connector (Fig. A).
NOTE: This connector is grey in color.
5 Plug the connectors from the PCIII inline
of the stock wiring harness (Fig.
B).
6 Bolt the fuel tank down into position.
7 Remove the bolt on the left hand side
of thefuel tank bracket and loosen the
right hand bolt enough to route the
PCIII harness underneath it (Fig. C).
8 Reinstall the bracket.
9 Attach the ground wire from the PCIII
to the negative side of the battery
(Fig. D).
10 Install the PCIII in the rear
section of the trunk (Fig. E).
This bike does not have a flat surface
to allow you to use the supp7 Remove the bolt on the left hand side
of thefuel tank bracket and loosen the
right hand bolt enough to route the
PCIII harness underneath it (Fig. C).
11 Make sure all the wires are
routed properly.
12 Reinstall the main seat and the passenger
seat.
cueist
Well-Known Member
2 brother slip on and pcIII
Hi,
I am planning on getting a 2 brothers slip on and a pcIII for my 08' FZ1.
I see a map for it for download but it also talks about a dyno o2 eliminator. What is this and is it necesary for an 08' non california model. Googleing it for an 08 model comes up with nothing of course its hard to find stuff for the 08 still. Thanks for your help.
cueist
Also if you happen to know if the 08' model has the 17 tooth front sprocket that everyone changes to 16 like on 06's and 07's, and if this would help with low speed driveing and manuvers? I know my spelling is off lol Thanks
Hi,
I am planning on getting a 2 brothers slip on and a pcIII for my 08' FZ1.
I see a map for it for download but it also talks about a dyno o2 eliminator. What is this and is it necesary for an 08' non california model. Googleing it for an 08 model comes up with nothing of course its hard to find stuff for the 08 still. Thanks for your help.
cueist
Also if you happen to know if the 08' model has the 17 tooth front sprocket that everyone changes to 16 like on 06's and 07's, and if this would help with low speed driveing and manuvers? I know my spelling is off lol Thanks
jskf16
www.fazerclub.gr
remember if you change it , your FZ1 it will write not right kilometers(odometer) in display!!
and then you need a speedohealer
SpeedoHealer - Electronic Speedometer and Odometer calibrator for motorcycles
HealTech Electronics Ltd. - Makers of the GIpro/ATRE and SpeedoHealer
[email protected]
Member
it really pays to zip tie the plug onto the control unit as the retaining plug/clip is crap caused me all sorts of problems
see my photo in the Gallery on FZ modds and pays to silicone the ignition module in place
see my photo in the Gallery on FZ modds and pays to silicone the ignition module in placetripp06fz1
Member
O2 Sensor
just bought a dynojet sensor eliminator. i've been looking all over for location of and instructions for the installation of this part. i bought the bike used (06 FZ1) with a PCIII and ivan FCE installed. messed around with some maps, specifically the stock exhaust/stock filter (though i have K&N) and O2 sensor disconnected. any help would be GREATLY appreciated!! my first post as a new member, but from reading on this site it sounds like there are plently of helpfull folks.
just bought a dynojet sensor eliminator. i've been looking all over for location of and instructions for the installation of this part. i bought the bike used (06 FZ1) with a PCIII and ivan FCE installed. messed around with some maps, specifically the stock exhaust/stock filter (though i have K&N) and O2 sensor disconnected. any help would be GREATLY appreciated!! my first post as a new member, but from reading on this site it sounds like there are plently of helpfull folks.
Hellgate
Wizard
I would HIGHLY recommend you locate a good dyno tuning shop in your area and have them tune your bike. Reason being the maps from DJ a pretty generic and well, stink. Unless you have a way to analyze the exhaust it is difficult at best properly tune PC3 to the bike. Once it's totally dialed in they are sweet! A good shop can knock this out for you in a day or two.
Last edited:
Lonerider59
Wizard
The O2 eliminator connects to your wiring harness where it normally gets it's signal from the stock A/F sensor. I't not necessary to remove the stock sensor, although I did because I have an A/F guage and installed a Bosch sensor to work with it. If your map calls for an O2 eliminator, the PCIII should come with it. It's a simple plug-in connector, very easy to put in and if you choose, you can just tie off the end of your stock sensor wire. I wouldn't do any cutting because those things are expensive and later on you might decide to reinstall it. Whoever you purchase the PBIII from, just ask them about the eliminator.
tripp06fz1
Member
really appreciate the help guys. a buddy from work suggested the same thing (taking it a specialist) but of course i just had to mess with it!! not sure if the pc came with anything as it was installed already on the bike when i purchased (from dealer)