Hey guys I've got some front end parts I no longer need for my FZ1. All of the parts are in great condition With the exception of the factory muffler. It appears someone's shoe may have melted to it at some point. Not really looking to make any money off of anything would rather just free up the...
Gen 2 headers for sale, honestly I do not know the brand of aftermarket headers that they are but they are not stock, seem older from the oxidation and unable to find the same set online now. I’ve started polishing them some and I’m sure with some patience they could really shine up nicely...
Hi Everyone,
I'm new to this site. I've been riding motorcycles for over 30 years now, and owned my 2006 FZ1 since new. Unfortunately, some life changes have interrupted my motorcycle riding and I no longer ride like I use to. I look at the FZ1 every day trying to figure out justification to...
hi im looking for exhaust colletts for my 2007 fz1/n but yamaha dont make them,, is there any other make and model that uses colletts that will fit my exhaust,, my email is [email protected] if u have any advice,,cheers,,
hi guys, i need advice please,, iv a 2007 fz1/n and i need colletts to fasten exhaust back on at manifold,, yamaha dont make colletts for this model so i was wondering if there was any other bike that uses colletts that will fit my exhaust so that i dont have to replace the whole system...
Hi folks..
Re my recently acquired 2006 Gen II FZ1.
Some simple work I did immediately. Opened the air box up as per posts on this website. New K&N filter. Disconnected EXUP cables and left the valve open, on stock exhaust.
My dyno tuner got rid of the fuel injection throttle...
Hi folks..
Just picked up a 2006 FZ1 that came with a short Yoshimura slip on. The bike has the notorious fuel injection on/off glitch, and the slip on made it worse, causing the bike to run lean and backfire. I'm arranging to have the ECU flash done, but have to wait a bit.
The bike came...
Hi everybody,
I'm new to forum, so howdy! I picked up a 2010 FZ1 about a month ago with only ~5300 miles on the odo (yay). I got the bike for a steal too. I'm looking at swapping the stock can for a new slip-on.
Will there be any issues if I just swap the can out (IE bike runs lean, loss...
Hello my friends! My fz1 recently started to make ticking noises from the engine, so i assumed it was in need of some new exhaust gaskets. However, when i unbolted the exhast, this is what i discovered:
Do you guys have any suggestions how i could re-attach the exhaust connector gasket to...
https://www.amazon.com/gp/product/B0784TFKW7/ref=ox_sc_act_title_3?smid=A32DD98RE9WXAK&psc=1
It looks nice but want to know how it sounds.
Thanks in advance
Hi all,
I have forsale a genuine Fz1 flyscreen with the fitting kit. £75 plus postage. Located in the UK
Also have:
Micron Serpant exhaust in black
Genuine bellypan in black
Single seat cowl in black
Gilles rearsets in silver
Evotech single exhaust hanger.
Pics to come
At the risk of jinxing myself, I'd just like to tell everyone how nice my bike feels lately.
Suspension is lovely
Exhaust note is lovely.
Handling is lovely.
I know most of you will understand.
Thankyou my lovely bike.
I hope you all are enjoying your rides!
I stupidly allowed my 74 yr old Aunt to Rev my bike from a cold start.
And more stupidly I watched her do it!
Check the video
https://www.youtube.com/watch?v=PczQCnahLr0
What damage do you think this has caused.
It may be just in my head but i think exhaust sounds a bit louder, the...
I do not want to separate this at this time and would like to sell it as a full kit. These were all pulled off my bike after my accident. There is no damage to the exhaust or other parts other than what's stated below.
- Full Graves exhaust
- BMC race filter
- Yoshimura Fender Elim kit the...
F/S: Scorpion Exhaust
*Update: Power Commander has been sold. Exhaust still for sale; Price has been updated.
Decided, after much deliberation, to go with stock exhaust on my 06' FZ1 clean-up project. For sale is this excellent condition Scorpion slip-on exhaust packaged with a Power...
WTB Gen1 Stock Exhaust Header/Collector
My #1 (or is it #4) pipe has a goodly sized dent it in. It was like that when I bought it. I don't want to spend the $$$ for a aftermarket header/exhaust system as I like it quiet.
So, anyone have one available? Preferably around the So-Cal...