2007 FZ1 front end parts for sale

ghetto_d

Well-Known Member
FIRST AND FOREMOST
I’m brutally honest, and I’m anal about my toys. These are take-offs of one of my personal machines (due to upgrade, not wrecked part-out). 100% functional and extremely clean. I’m on FZOA, 998CC, R1-FORUM, local PNW forums (GHETTO_D), & EBAY (GHETTO_CRUIZER). So, check my references. I know how to package stuff so it doesn’t get damaged. Forum prices here - You save me fees, and I’ll save you money. I like combining shipping…

2007 FZ1 front end parts for sale. 11k miles. You can assume all parts are as perfect as used parts can be, unless I state otherwise. Prices are OBO. All photos taken under very discriminating LED lighting.

FZ1 Forks: SOLD
PN: 2D1-23102-13-00, 2D1-23103-13-00
Gold tubes, gold caps. Very good condition. Off a bike that has never been wrecked. Never opened up (caps are perfect). To nitpick: couple dimples in upper tubes from rocks, etc.; some scuffing on uppers from triple clamps; factory/previous owner looks to have possibly over tightened the triples around the forks, so you can see a couple slight impressions in the uppers (probably ~.001” indentation (I’m a machinist, trust me)).

FZ1 F Axle: $10+ship
PN: 4XV-25181-10-00
It had a bit of corrosion on hex end when I purchased bike, but I ground and polished it out. Now it looks better than yours. Fits a multitude of bikes (FZ1 FZ6 R1 R6 FJR1300)

FZ1 F Calipers, pads: SOLD
PN: 2D1-2580T-00-00, 2D1-2580U-00-00
Even wear on pads. Minty fresh looking & operating calipers.

FZ1 Rotors: SOLD
PN: 5D0-2581T-10-00
Even wear. Some typical slight chipping of the black paint on outer edge.

FZ1 F Master Cylinder: $50 shipped
PN: 3C3-W2587-00-00 et al
Looks and performs great.

FP Racing Brake & Clutch Levers (adjustable) for FZ1 06+ $120 shipped
Long length. Pewter lever color with natural/silver adjuster color. Basically perfect condition, with a couple slight marks in points of contact - nothing visible. Only one season of use.
 

Attachments

  • IMG_3091.jpg
    IMG_3091.jpg
    64.6 KB · Views: 70
  • IMG_3094.jpg
    IMG_3094.jpg
    79 KB · Views: 68
  • IMG_3087.jpg
    IMG_3087.jpg
    64.4 KB · Views: 67
  • IMG_3086.jpg
    IMG_3086.jpg
    63.5 KB · Views: 67
  • IMG_3048.jpg
    IMG_3048.jpg
    70.4 KB · Views: 68
  • IMG_3050.jpg
    IMG_3050.jpg
    65.9 KB · Views: 64
  • IMG_3064.jpg
    IMG_3064.jpg
    65.7 KB · Views: 65
  • IMG_3093.jpg
    IMG_3093.jpg
    58.1 KB · Views: 64
  • IMG_3089.jpg
    IMG_3089.jpg
    63.3 KB · Views: 63
Last edited:
more pics of the parts listed above.
 

Attachments

  • IMG_3103.jpg
    IMG_3103.jpg
    84.7 KB · Views: 56
  • IMG_3101.jpg
    IMG_3101.jpg
    72.2 KB · Views: 55
  • IMG_3100.jpg
    IMG_3100.jpg
    62.4 KB · Views: 55
  • IMG_3099.jpg
    IMG_3099.jpg
    55.7 KB · Views: 55
  • IMG_3098.jpg
    IMG_3098.jpg
    67.3 KB · Views: 58
rotors pics are "overall" and then "detailed" of the worst areas
i'd say these look great from 5 feet. up close, they have their flaws.
both are very true though, and both measure at 4.7mm. i just measured a set of new rotors at 4.95mm.
IMG_3106.jpgIMG_3108.jpgIMG_3109.jpgIMG_3110.jpgIMG_3112.jpgIMG_3114.jpgIMG_3115.jpg
 
Back
Top