Hello & Welcome to our community. Is this your first visit? Register

Search:

Type: Posts; User: justpassinthru

Search: Search took 0.00 seconds.

  1. Replies
    5
    Views
    233

    I suggest getting used to it a little at a time. ...

    I suggest getting used to it a little at a time.
    That's the reason it has a throttle, just give it what you can handle.
  2. EXUP working and cables adjusted properly? ...

    EXUP working and cables adjusted properly?
    Maybe sonic clean the carbs.
  3. Replies
    7
    Views
    2,464

    I ran into that several years ago. Found a...

    I ran into that several years ago.
    Found a metric bolt and nut with a 19mm head and welded the nut to the bolt. It's been working fine.
  4. A whole lot of people have fallen in love with...

    A whole lot of people have fallen in love with these bikes.
  5. Doubt you hurt the engine with the starter. If...

    Doubt you hurt the engine with the starter.
    If an o ring on a seat is cracked or the needle valve is bad, tapping on the carb will do nothing. I might try gently tapping on one to get me home, but...
  6. Sounds like it's time to rebuild the carbs. If...

    Sounds like it's time to rebuild the carbs.
    If a lot of gas is getting above the piston, that would explain the no crank issue because liquids do not compress.
    Might want to check the oil too...
  7. Replies
    5
    Views
    190

    Any time a rebuild a carburetor I test it with...

    Any time a rebuild a carburetor I test it with this....
  8. Replies
    5
    Views
    190

    Apparently, you missed something. You know what...

    Apparently, you missed something.
    You know what you gotta do.
  9. Not to worry, that new $30,000 Electric turd they...

    Not to worry, that new $30,000 Electric turd they have for sale will pull them through.lolup

    Electraturd, Turdglide or something of the like, is what they should call it.
  10. You're asking me which forum??? You're the one...

    You're asking me which forum???
    You're the one who mentioned another forum in post number 11 and I quote: "Thank you, I will try to reach folks through the other forum. I appreciate this."
    OK,...
  11. Replies
    5
    Views
    202

    https://www.delcity.net/images/linedrawings/Relay%...

    https://www.delcity.net/images/linedrawings/Relay%20Diagram.pdf
    Numbers 85 and 86 are for the power and ground to energize the relay coil (doesn't matter which goes where), the 30 pin will be...
  12. Replies
    5
    Views
    202

    If you want the grips controlled by the ignition,...

    If you want the grips controlled by the ignition, you really should use an existing ignition powered circuit to energize the coil on a relay and run the power circuit for the grips through that...
  13. Replies
    5
    Views
    202

    I believe I would come straight from the battery...

    I believe I would come straight from the battery or out of a power outlet straight from the battery.
  14. You said the only way to hear this noise is by...

    You said the only way to hear this noise is by turning the crank with a wrench at the left side of the engine, and that it is quiet when running.
    Why did your mechanic have the left side cover off...
  15. The bike might actually have a problem with...

    The bike might actually have a problem with second gear.
    It wouldn't be the first.
  16. You said "it would cost another $400+" What...

    You said "it would cost another $400+"

    What has been done to the bike already by this guy?
  17. Do you hear anything while it's running? Any...

    Do you hear anything while it's running? Any engine has clearance between the bearings and the crankshaft that is filled with oil when it's running, that may be what you're hearing. If it's quiet...
  18. Replies
    6
    Views
    272

    That's where coolant comes out if it gets past...

    That's where coolant comes out if it gets past the seal.
    Otherwise, it could get mixed with the engine oil.
  19. Replies
    6
    Views
    272

    Leak

    Water pump.
  20. Replies
    1,615
    Views
    153,069

    Sticky: It's been a week since I joined here. I tried to...

    It's been a week since I joined here. I tried to post in another thread with the intention of adding some useful information to that thread, but it had to be approved by a moderator before it would...
  21. Replies
    4
    Views
    997

    Old thread but still, this might help someone. ...

    Old thread but still, this might help someone.
    http://www.iowaz.info/cycle/fz1manual.pdf
  22. Replies
    1,615
    Views
    153,069

    Sticky: New Member in NC

    Still riding the 2005 FZ1 I bought in 2007 and love it more each time I get on it.
    IMHO, the gen1's are one of the best bikes ever built, they just plain got it right!
Results 1 to 22 of 22
All times are GMT -8. The time now is 12:47 AM.
Powered by vBulletin® Version 4.2.5
Copyright © 2019 vBulletin Solutions Inc. All rights reserved.
Search Engine Optimisation provided by DragonByte SEO (Pro) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.


Copyright ©2008 , All content is property of 998cc.org All Rights Reserved. The opinions and posts on this site do not necessarily reflect those of the site owners or operators. Yamaha FZ1 and Yamaha rights are property of Yamaha Motor Company. 998cc.org is not associated with Yamaha in any way. We are an enthusiast site dedicated to the Yamaha FZ1 motorcycles. Our goal is to offer a place for Yamaha FZ1 owners to discuss rides, events, mods, maintenance, purchasing, etc.
vBulletin Skin By: PurevB.com